August 31st, 2010
In an increasingly complex world where more and more reliance is placed on technology, the consequences when things go wrong can be financially and economically severe. In the past, if a horse threw a shoe or a bucket got a hole it was just fixed and life carried on. However if a pipeline fails or a safety system malfunctions the results can be widespread and effect lots of people and the environment.
It is at times like this that it is necessary to trace back to the cause of the problem, not to allocate blame, but to find out what went wrong and ensure it does not happen again. A good example of this is air crash investigations. They are there to find out what failed and check if it may be a risk to other aircraft of the same type.
These investigations require traceability of all components in any system. In pipelines, if pipe fittings or pipe flanges fail it is necessary to trace the source of those components to see if there was a manufacturing fault.
For the overall project the documentation on the procurement of components will form part of the project quality plan. This document is built up over the lifetime of a project and will include details from inception, design, installation and testing. It will form an invaluable tool to the maintenance personnel and can assist if things go wrong.
We at Chemipetro place a high value on quality control and can provide all the necessary documentation, test result and certification for all products we supply to ensure that our clients can meet their quality plan requirements.
Tags: Pipe Fittings, Pipe Flanges, pipe joints, pipeline
Posted in Pipe Fittings | No Comments »
August 27th, 2010
In all field of engineering, especially the petrochemical industry, there are a wide range of design and regulatory standards that should be adhered to when designing a pipeline and its component parts.
However there is a significant difference between what it is legally required to carry out and what is advisory and it is important for the pipeline designer to know the difference between the two.
The Pipeline Safety Regulations are mandatory and legally must be adhered to. However apart from setting general standards they do not stipulate how they are to be complied with. That is the responsibility of the designer and the pipeline operating company.
Design standards on the other hand such as British Standards are advisory documents. They stipulate what is good practice and what the common standards should be to ensure compatibility of components between manufactures such that pipe fittings from one manufacturer will fit with pipe flanges from another manufacturer. They also set the standards for materials such as duplex and super duplex stainless steels so that the purchaser can be assured of the quality of the material being purchased.
At Chemipetro we manufacture a wide range of pipe fittings and component parts to internationally recognised standards.
However they are not meant to deter design innovation and development. So a new component can be used even if it does not specifically meet the standards as set down in a related British Standard provided it can be provided that it does not reduce recognised safety standards in operation.
So although the designer must adhere to regulations, they can develop new ideas without unnecessary constraints.
Tags: Duplex, Pipe Fittings, Pipe Flanges, Super Duplex
Posted in Pipe Fittings | No Comments »
August 24th, 2010
Pipeline installations are designed to have a long economic life span. After all they are very expensive infrastructure investments which are costly to replace. Pipeline engineers therefore specify the best materials to meet this prolonged life expectancy such as duplex and super duplex stainless steels. They also ensure high quality engineered products for pipe fittings and flanges.
As a result of these high standards of material, the petrochemical industry generally has a good safety record considering the millions of litres of dangerous fluids and gasses that are processed each day. However, as witnessed by recent events in the Gulf of Mexico, even in the best run worlds things can go wrong.
The Pipelines Safety Regulations, recognise this fact and specifically states under item 12 that before any fluid is allowed to flow in the pipeline the pipeline operator must make specific provision for dealing with:
a) the accidental loss of fluids from the pipeline
b) defects or damage to the pipeline
c) any emergency effecting the pipeline
The pipeline operator must therefore have a safety regime in place that can deal with any type of emergency that may arise. This can be expensive if it is necessary to hold in stock replacements for each type and size of pipe fitting used in an installation.
Therefore in order to assist our clients to meet this obligation, we at Chemipetro offer a 24 hour emergency breakdown call out service. We also hold in stock a wide range of pipes and pipe fittings so that any problem can be dealt with as speedily as possible.
Tags: Flanges, Pipe Fittings, Pipe Flanges, Super Duplex
Posted in Flanges | No Comments »
August 21st, 2010
When the first of any type of system is designed and installed, it is done to suit the practicality of what is required. Performance is the initial objective and a design is judged by how well it achieves its goals, does it go fast enough? Deliver enough? Is it strong enough?
Very soon, problems are identified. These may be problems with performance or they may be problems with safety. It becomes apparent that if a design is to be repeated and adapted, but without repeating mistakes, then some form of written design or safety standard is required.
With the pipeline industry in the UK these are ‘The Pipeline Safety Regulations 1996’. These were enacted as part of the ‘Health and Safety Act’ of 1974.
These regulations cover the design principles required for any pipeline used for conveying gas or fluids, which is not a drain or part of a heating system, and refers particularly to fluids considered ‘dangerous’, which relates to the petrochemical industry.
Part II item 7 specifically states that the pipeline must be designed so that maintenance and inspection work can be carried out safely.
One way of achieving this is to ensure that joints with bolted flanges are located at suitable locations to allow the critical sections of the pipeline to be dismantled. Also, suitable pipe fittings are provided where required such as isolation valves, to ensure that sections can be isolated and drained for working.
We at Chemipetro supply a wide range of flanges and pipe fittings to ensure that your design will comply with the safety regulations.
Tags: Flanges, Pipe Fittings, Pipe Flanges, pipe joints
Posted in Pipe Fittings | No Comments »
August 18th, 2010
In any design application one of the key considerations is what material is used to produce a specific item. The material needs to be able to cope with the mechanical stresses that may be imposed upon it, from mechanical shock to exposure to high temperatures and pressures. Equally the application must not be over engineered, utilising a material that is overly heavy or costly for a specific job, otherwise this will simply make the project uneconomic. Designers need to be sure that the material they are selecting is the correct one for that specific application.
For example, in the design of heat exchangers it is necessary that the material is not only strong and can withstand the high temperatures and pressures to which it will be exposed, but it is also important that it has good thermal conductivity characteristics. Also, in the petrochemical industry the material must be resistant to corrosion from the various chemicals that it will handle.
Super duplex steel is an excellent material from this stand point. Although it may be more expensive per tonne than ordinary steels, its corrosion resistant properties will ensure it requires less maintenance. Also, it has a low co-efficient of thermal expansion which means that where it is used in applications such as heat exchangers, it will be under less mechanical stress.
We at Chemipetro produce a wide range of pipes, pipe fittings and flanges from super duplex stainless steel and can meet whatever design features your design may require.
Tags: Flanges, Pipe Fittings, Pipe Flanges, Super Duplex
Posted in Pipe Fittings | No Comments »
August 15th, 2010
One of the most fundamental problems faced in any industry is how to join two pieces of material together. A layman asked this question would probably immediately think of glue. This is possible even with steel, where welding is effectively gluing two pieces of metal together.
There are however two fundamental problems with any sort of glued joint. The first, the joint is only as strong as the glue itself. To help overcome this with welded joints the ends of the pieces are shaped to form a V. This gives the weld a greater surface to form on and so make the bond stronger.
The second problem is that any glued joint is permanent and does not allow for anything to be dismantled should maintenance be required.
To dismantle a joint it should be connected by a removable fastening. This is where the humble nut and bolt come in. By providing flanges on the end of a pipe or a pipe fitting, and by bolting the two flanges together, a strong but removable coupling can be achieved.
But what sort of nut and bolt should be used? In concept they may all be the same but in practice they can be very different, from a simple threaded rod which is cut to length, to a 12 point ferry head unit. The choice of nuts can also be bewildering from the simple hexagonal to a bi hexagonal 12 point self locking type.
Whatever your need we at Chemipetro can provide a wide range of fastenings to meet your specific requirements even if it is a non standard and unique type.
Tags: Flanges, pipe fitting, Pipe Flanges, welded joints
Posted in Pipe Flanges | No Comments »
August 3rd, 2010
When it comes to quality of materials, the petrochemical industry can take no chances. A failure of pipelines or pipe fittings such as a flanges or couplings in service can be catastrophic and very costly in terms of damage and lost production.
It is therefore important that all materials are rigorously tested before they are dispatched, as small irregularities in the crystalline structure of the steel can cause fractures, which in turn cause the material to fail when subjected to high pressure and temperatures. It is important to detect these irregularities and specialist detection techniques have to be used.
One such technique is Magnetic Particle Inspection. At some time almost everyone will have carried out an experiment at school where a sheet of paper is laid over a magnet and then iron filings sprinkled over the paper. The iron filings will then align themselves to display the lines of the magnetic field.
Magnetic Particle Inspection is similar in principle, albeit more sophisticated. The part to be tested is subjected to an electromagnetic field to magnetise it. It is then coated with iron oxide either in powder form or in a liquid suspension. Any irregularities in the steel cause an irregularity in the magnetic field, which can be seen in the patterns in the iron oxide. These irregularities can indicate possible faults in the material which can then be investigated further.
At Chemipetro we supply quality materials such as pipe flanges, and we can carry out several specialist testing techniques on critical parts including Magnetic Particle Inspection to ensure the quality of our products.
Tags: Flanges, Pipe Fittings, Pipe Flanges, pipe joints
Posted in Pipe Fittings | No Comments »
July 30th, 2010
How lengths of pipe and pipe fittings are actually connected together would seem, on the face of it, to be a relatively simple exercise but in fact it is a very complex issue.
It is possible to use pipe flanges, but this is an expensive option and is really only suitable for situations where the pipework has to be dismantled for maintenance, as all bolted flanges introduce a weakness.
It is possible to use a threaded connection where the end of one pipe is screwed into the end of another pipe. This method is commonly used for smaller pipe sizes. However the cutting of the thread reduces the thickness of the pipe material and so again introduces a weakness.
The preferred option for joining pipe lengths is a welded joint. But again there are different options depending upon the application. The most common type is the butt weld. This is a connection between two pipes of the same size. The end of each pipe is bevelled so that when the two ends are placed together a V is formed. The pipes are then welded around this V.
However in situations where there are high pressures and the flow characteristics are important, a socket weld can be used. Here one of the pipes has a larger collar which fits over the other pipe. The weld is then done on the outside. These are easy to use especially on small bore pipes.
Whatever type or pipe connection you propose to carry out, we at Chemipetro manufacture a wide range of pipe fittings and pipe flanges to meet all your requirements.
Tags: Flanges, Pipe Fittings, Pipe Flanges, socket weld
Posted in Pipe Flanges | No Comments »
July 27th, 2010
Most people when asked to design a pipeline would simply draw a pipe from point A to point B. However there is much more to the design of a pipeline than this.
To start with, the pipe has to be correctly sized to cope with the volume flow rate required. If the pipe is too small then it will take more pump pressure to force the required amount of liquid though it. A higher pressure will also require a stronger pipe and pipe fittings. If it is too large then it is just a waste of materials and money.
Another consideration is the temperature of the liquid flowing through the pipe. Although we think of steel pipes as pretty solid things that do not move, in practice the metal will expand when exposed to even relatively moderate temperatures. The result of this is that over a distance there can be considerable movement. As an example a 30m length of steel pipe carrying steam at 150°C will expand nearly 63mm.
To counter this, it is necessary to introduce expansion loops that allow the pipe run to deform and take up this movement. The size and number of these loops has to be carefully calculated to prevent over stressing the welded and flange connections.
We at Chemipetro can supply a wide range of pipes, flanges and pipe fittings made from varying materials such as duplex and super duplex stainless steels to ensure that the pipeline designer can always specify the correct material for the job at hand.
Tags: Flanges, Pipe Fittings, Pipe Flanges, Super Duplex
Posted in Pipe Fittings | No Comments »
July 21st, 2010
As well as a wide range of pipe fittings and pipe flanges, we at Chemipetro manufacture an extensive range of pipes for use in the petrochemical industry. But this is not all we do as we also manufacture a range of seamless pipe especially designer for use in boilers and heat exchangers.
On first considerations this may seem like it is moving outside our normal field but in the processing of chemicals there is a regular requirement for these. Whilst we are all very familiar with boilers, what exactly is a heat exchanger?
Heat exchangers and boilers are very similar in function in that they are used to transfer heat from one medium to another. In the case of a boiler the heat comes from the combustion of a fuel producing a hot gas. This hot gas is then used to heat a second liquid, which in the case of boilers is water.
In a heat exchanger the process is similar in that heat is transferred from one medium to another, but in this case they are usually both liquids. A hot liquid runs through the primary tube transferring heat to a second liquid on the secondary side. By passing a cold liquid through the primary tube, they can also be used for cooling.
The common link between boilers and heat exchangers is that they are called to handle liquids over a wide range of temperatures and high pressures and that the pipes used to manufacture them must be of the highest standards. So perhaps not so outside our field as you might first think.
To view a wide range of pipe fittings and flanges on their website, visit Chemi Petro’s website today.
Tags: Flanges, pipe fitting types, Pipe Fittings, Pipe Flanges
Posted in Pipe Fittings | No Comments »
